Yes I know, I've stated i don't work on hpa guns but everyone has to start somewhere. Overall an F2 Engine was installed into this gun as well as a ton of cosmetic changes such as a new front handguard, fresh white coat of paint and other small details.

The start of a journey into the future of airsoft performance, A cyma p90 with a complete over hall including a custom microswitch etu setup allowing for programable firing modes as well as other goodness the Perun etu++ offers. The start of my p90 addiction.

Complete custom built m4 that I have repurposed as a personal project rifle, built up from my first airsoft gun this upgraded version includes a completely new gearbox with high-speed gears, high torque motor, sp95 equivalent spring, Perun optical Mosfet as well as many other changes internally and externally.

Stock Cyma Platinum m4 which received an upgrade in the form of a Perun optical Mosfet as well as a new o ring on the piston head. Gun perfomed at a rps of 25 with good range and power using a 11,1V lipo.

Ares Honeybadger came in with stripped gears, doing 320 fps on an sp100 spring before the breakdown. The stripped gears have been replaced and re shimmed, as well as the o ring on the piston head was replaced which resulted in the gun shooting 360 fps, with that the customer replaced the stronger spring back to the stock spring bringing the fps down to 340-350.

Lancer tactical donor gearbox was to be assembled and put inside of an m4 lower receiver. The gun received a rewire as well as a modified tappet plate, new cut of leaver, piston head realignment as well as other small fixes and modifications. In the end, the complete gearbox set performed well with a swapped out 16:1 gearset (which was damaged) for a 13:1 cyma CNC gear set which paired perfectly with the high torque motor which was being used.

This g&g rk47 is one of a kind trust me, and i'm not talking about the paint job but what it took to get it to work correctly. the gun arrived to me damaged only doing 230 fps on 0.2s, i have completely disasablmed the gun, cleaned it internally, shimmed and replaced worn out parts. the cylinder, cylinder head, piston and piston head have been replaced by a cyma platinum cylinder set along with the hop rubber.

After this the gun was doing 300 fps on 0.2s bbs with a decent range which was tested out during a gameday on which the weapon scored 2 kills within a 20m range.a one of a kind hello kitty paint job was also applied onto the weapon to give it a non usual look that is eye-catching. Parts such as the rear sight and butt plate were custom 3d printed since they were missing when the weapon arrived to me

This R28 piston has trigger reset issues as well as a sluggish slide return. a new sear spring set was put inside as well as a deep clean and re lubrication of the internals was performed.

+ both mags had leaking issues, they were both cleaned and re-lubricated which fixed the leaking problems.

custom DSG build purposed for this krytac, arrived to me fully disassembled needing a lot of love and care as the previous owner of this gun attempted to put the gun together to have just break and strip gears instantly.

I have re-seat the mosfet, apply a new o ring on the piston head, do some aoe correcting with a small space so that the gears do not engage and damage the piston rack. the gun also required a new hop unit as the one supplied was unable to hop .25 bbs, as well had a glued in bucking, an interesting build for sure.

Complete upgrade package in the form of a Perun v2 hybrid MOSFET unit which allows for adjustable trigger pull as well as pre-cocking and other handy features. The replica also received an fps boost from 210 fps on .25 bbs up to 300 fps. Other smaller modifications such as the installation of an ICS flat trigger and ergonomic pistol grip have also been integrated.

From broken nozzles to a piston shattering into a thousand pieces, this for sure was my least favourite project so far. In the end, a Perun v2 hybrid was installed to fix inconstant semi fire as well as provide an overall upgrade. Not to mention the bent outwards gearbox and amazing ics hop-up, this was one hell of an adventure for sure.

Paint job commissioned by a local skirmish field. Decided it was time to spice up some of their rental guns as part of their sniper package, overall I am very pleased with the result considering it is an ares after all.

same as before, a quick paint job for a local site

Bought this beauty from the patrol base boneyard section, a good deal for once? cant be. listed to have a hammer/slide lockup issue however, after receiving the pistol I realised there isn't anything inherently wrong with it apart from the part where it shoots full auto but we can look over that. the pistol has been stripped and worn out parts such as the sear springs have been replaced. in the end, I get my self a nice little pistol.

The gun arrived completely trashed, twisted and bent handguard, thick grey spray paint and a dead etu. What more would you want?  The spray paint was removed with it came alignment of the front handguard which was then followed by the swift installation of a Perun Hybrid mosfet.